NORYL RESIN HS2000X 25 kg SABIC

Nombre del producto: OTR – MFI7.6 – SABIC – NORYL RESIN HS2000X
Categoría: Otros
Información del manual del producto: Revision 20231109
NORYL™ RESIN HS2000X
REGION AMERICAS
DESCRIPTION
NORYL HS2000X resin is a 17% mineral reinforced blend of polyphenylene ether (PPE) + polystyrene (PS). This injection moldable grade contains non-
brominated, non-chlorinated flame retardant and carries a UL94 flame rating of 5VA at 2mm and V0 at 1.5m along with UL746C Outdoor Suitability
rating of F1. NORYL HS2000X resin exhibits strong electrical performance, dimensional stability, very low moisture absorption, and hydrolytic stability. This
material is an excellent candidate for electronic / electrical indoor and outdoor applications including air conditioner parts, smoke detector covers, pool
+ spa pump parts and housings.
GENERAL INFORMATION
Features
Flame Retardant, Hydrolytic Stability, Low Warpage, Amorphous, Low Shrinkage, Low Moisture Absorption,
Non Cl/Br flame retardant, Non halogenated flame retardant, Dimensional stability, High
stiffness/Strength
Fillers
Mineral
Polymer Types
Polyphenylene Ether + PS (PPE+PS)
Processing Techniques
Injection Molding
INDUSTRY
SUB INDUSTRY
Building and Construction
Building Component, Water Management
Consumer
Home Appliances, Commercial Appliance
Electrical and Electronics
Electronic Components, Mobile Phone – Computer – Tablets
Industrial
Electrical
TYPICAL PROPERTY VALUES
PROPERTIES
TYPICAL VALUES
UNITS
TEST METHODS
MECHANICAL
Tensile Stress, yld, Type I, 5 mm/min
74
MPa
ASTM D638
Tensile Stress, brk, Type I, 5 mm/min
60
MPa
ASTM D638
Tensile Strain, yield
3.8
%
ASTM D638
Tensile Strain, brk, Type I, 5 mm/min
8.4
%
ASTM D638
Tensile Modulus, 5 mm/min
3650
MPa
ASTM D638
Flexural Stress, brk, 1.3 mm/min, 50 mm span
117
MPa
ASTM D790
Flexural Stress, yld, 2.6 mm/min, 100 mm span
117
MPa
ASTM D790
Flexural Modulus, 1.3 mm/min, 50 mm span
3670
MPa
ASTM D790
Flexural Modulus, 2.6 mm/min, 100 mm span
3550
MPa
ASTM D790
Tensile Stress, yield
71
MPa
ISO 527
Tensile Stress, break
57
MPa
ISO 527
Tensile Strain, yield
3.7
%
ISO 527
Tensile Strain, break
10.5
%
ISO 527
Tensile Modulus, 1 mm/min
4000
MPa
ISO 527
Flexural Stress
117
MPa
ISO 178
Flexural Modulus
3800
MPa
ISO 178
IMPACT
(1)
(1)
© 2023 Copyright by SABIC. All rights reserved
PROPERTIES
TYPICAL VALUES
UNITS
TEST METHODS
Izod Impact, unnotched, 23°C
2230
J/m
ASTM D4812
Izod Impact, notched, 23°C
131
J/m
ASTM D256
Izod Impact, Reverse Notched, 3.2 mm
811
J/m
ASTM D256
Instrumented Dart Impact Total Energy, 23°C
60
J
ASTM D3763
Izod Impact, notched 80*10*4 +23°C
9
kJ/m²
ISO 180/1A
Charpy Impact, notched, 23°C
10
kJ/m²
ISO 179/2C
THERMAL
HDT, 0.45 MPa, 3.2 mm, unannealed
117
°C
ASTM D648
HDT, 1.82 MPa, 3.2mm, unannealed
108
°C
ASTM D648
HDT, 0.45 MPa, 6.4 mm, unannealed
128
°C
ASTM D648
HDT, 1.82 MPa, 6.4 mm, unannealed
116
°C
ASTM D648
CTE, -40°C to 40°C, flow
7.06E-05
1/°C
ASTM E831
CTE, -40°C to 40°C, xflow
7.76E-05
1/°C
ASTM E831
Vicat Softening Temp, Rate B/50
132
°C
ISO 306
Vicat Softening Temp, Rate B/120
136
°C
ISO 306
HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm
126
°C
ISO 75/Be
HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm
111
°C
ISO 75/Ae
Relative Temp Index, Elec
100
°C
UL 746B
Relative Temp Index, Mech w/impact
85
°C
UL 746B
Relative Temp Index, Mech w/o impact
100
°C
UL 746B
PHYSICAL
Specific Gravity
1.25
–
ASTM D792
Mold Shrinkage, flow, 3.2 mm
0.5 – 0.7
%
SABIC method
Melt Flow Rate, 280°C/5.0 kgf
7.6
g/10 min
ASTM D1238
Melt Flow Rate, 300°C/5.0 kgf
7.6
g/10 min
ASTM D1238
Melt Volume Rate, MVR at 280°C/5.0 kg
6
cm³/10 min
ISO 1133
Melt Volume Rate, MVR at 300°C/5.0 kg
6
cm³/10 min
ISO 1133
ELECTRICAL
Volume Resistivity
1.2E+16
Ω.cm
ASTM D257
Surface Resistivity
>1.E+16
Ω
ASTM D257
Dielectric Strength, in oil, 3.2 mm
17.3
kV/mm
ASTM D149
Relative Permittivity, 50/60 Hz
2.89
–
ASTM D150
Relative Permittivity, 1 MHz
2.7
–
ASTM D150
Dissipation Factor, 50/60 Hz
0.017
–
ASTM D150
Dissipation Factor, 1 MHz
0.0044
–
ASTM D150
High Voltage Arc Track Rate {PLC}
3
PLC Code
UL 746A
Comparative Tracking Index (UL) {PLC}
2
PLC Code
UL 746A
High Amp Arc Ignition (HAI), PLC 2
≥3
mm
UL 746A
High Amp Arc Ignition (HAI), PLC 3
≥1.5
mm
UL 746A
Hot-Wire Ignition (HWI), PLC 0
≥1.5
mm
UL 746A
Arc Resistance, Tungsten {PLC}
6
PLC Code
ASTM D495
FLAME CHARACTERISTICS
UL Yellow Card Link
E121562-221170
–
–
UL Recognized, 94-5VA Flame Class Rating
≥2
mm
UL 94
UL Recognized, 94V-0 Flame Class Rating
≥1.5
mm
UL 94
(1)
(2)
(2)
(2)
(1)
(3)
(1)
(2)
© 2023 Copyright by SABIC. All rights reserved
PROPERTIES
TYPICAL VALUES
UNITS
TEST METHODS
Radiant Panel Listing
–
UL Tested
Glow Wire Flammability Index, 1.0 mm
960
°C
IEC 60695-2-12
Glow Wire Flammability Index, 2.0 mm
960
°C
IEC 60695-2-12
Glow Wire Flammability Index, 3.0 mm
960
°C
IEC 60695-2-12
Glow Wire Ignitability Temperature, 1.0 mm
850
°C
IEC 60695-2-13
Glow Wire Ignitability Temperature, 2.0 mm
800
°C
IEC 60695-2-13
Glow Wire Ignitability Temperature, 3.0 mm
800
°C
IEC 60695-2-13
UV-light, water exposure/immersion
F1
–
UL 746C
INJECTION MOLDING
Drying Temperature
105 – 110
°C
Drying Time
3 – 4
Hrs
Drying Time (Cumulative)
8
Hrs
Maximum Moisture Content
0.02
%
Melt Temperature
280 – 310
°C
Nozzle Temperature
280 – 310
°C
Front – Zone 3 Temperature
270 – 310
°C
Middle – Zone 2 Temperature
260 – 305
°C
Rear – Zone 1 Temperature
250 – 300
°C
Mold Temperature
75 – 105
°C
Back Pressure
0.3 – 0.7
MPa
Screw Speed
20 – 100
rpm
Shot to Cylinder Size
30 – 70
%
(1) The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
(2) UL Ratings shown on the technical datasheet might not cover the full range of thicknesses, colors and regions. For details, please see the UL Yellow Card.
(3) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is
recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
(4) Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall
molding and gas-assist molding.
DISCLAIMER
Any sale by SABIC, its subsidiaries and affiliates (each a “seller”), is made exclusively under seller’s standard conditions of sale (available upon request) unless agreed
otherwise in writing and signed on behalf of the seller. While the information contained herein is given in good faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED,
INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE
PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each customer must determine the suitability of seller
materials for the customer’s particular use through appropriate testing and analysis. No statement by seller concerning a possible use of any product, service or design is
intended, or should be construed, to grant any license under any patent or other intellectual property right.
(4)
© 2023 Copyright by SABIC. All rights reserved