Polipropileno Copolímero Random SL262MW Indelpro
Nombre del producto: PP – RANDOM – MFI1.8 – INDELPRO – SL262MW
Categoría: Polipropileno
Información del manual del producto: 14/06/21
Page 1 of 2
SL262MW
POLYPROPYLENE, CLARIFIED RANDOM COPOLYMER FOR BLOW MOLDING
Profax SL262MW is an ultra-clarified random copolymer that provides good stiffness and low odor and taste
transfer; it exhibits excellent clarity. SL262MW has a wide processing window that helps to reduce the melt
temperature and cycle time contributing to energy savings. This resin improves the appearance and
aesthetics of the finished parts.
The base resin in this product meets the requirements of the US Food and Drug Administration (FDA)
contained in the Code of Federal Regulations in 21 CFR 177.1520.
Features: Typical Applications:
Low odor and taste transfer
Injection and extrusion blow-molding
Greater clarity and gloss than traditional grades
Thermoformed containers and lids
Better product aesthetics
Multilayer sheets
Wide processing window
Cycle time reduction and energy savings
Good rigidity and impact resistance
Profax SL262MW: CLARIFIED RANDOM COPOLYMER
Typical resin properties(a)
Typical value
ASTM Method(b)
-Melt flow rate (MFR), g/10 min
1.8
D1238
-Tensile strength at yield, psi (MPa)
3,770 (26)
D638
-Notched Izod impact strength at 73°F, ft-lb/in (J/m)
6.0 (306)
D256A
-Elongation at yield, %
13
D638
-Flexural Modulus, psi (MPa)
130,500 (900)
D790A
-Density, g/cm3
0.9
D792A
-Heat Deflection Temperature at 66 psi (0.46 MPa), °F (°C)
176 (80)
D648
(a)
Values shown are averages not to be construed as product specifications.
(b) ASTM methods are the latest under the Society’s current procedures. All specimens are prepared by injection molding.
R Profax is a trademark of Lyondellbasell Printed in Mexico
Made in Mexico under specifications of Lyondellbasell Inc.
14/06/21
Page 2 of 2
Additional information
Health and security
The resin is produced under the highest standards of safety and quality. Special attention is required for applications such
as food contact and direct medical use. For specific regulatory compliance information, please contact your local supplier
or Indelpro service department. Personnel who work during the processing of the material must be protected from possible
contact in the skin and eyes with molten material; the use of safety glasses and gloves is the minimum safety requirement
for those who may come into contact with the material during its melting and processing.
The material if during processing is exposed to the environment or severe processing conditions could become degraded,
generating by-products with an unpleasant smell and that in high concentrations could generate irritation in the skin, eyes
and any part of the body exposed to contact. Work areas where the resin is processed must be adequately ventilated to
remove fumes and vapors, all legislation in the control of emissions must be complied with.
The Resin will burn when it is in contact with excessive heat and oxygen. It must be handled and stored away from direct
contact with flames or sources of ignition. In case of combustion, the resin contributes as fuel and can generate dense
black smoke. Resins that are recycled or reused may have been used for the handling or packaging of hazardous
materials or have been in contact with them. Those who are using recycled or reused material are responsible for taking
the necessary precautions and ensuring that the recycled material is suitable for use.
For more information on safety, handling and processing please refer to the product safety data sheet.
Transportation and Handling
The transport and handling equipment must be designed and have the necessary measures to prevent the generation and
accumulation of fines and dust particles derived and / or contained in the resin. Under certain circumstances such
particles pose the risk of explosion. Transport systems must always be grounded, equipped with filters and be under
inspection and preventive maintenance programs.
Packing and Storage
The resin is packaged and marketed in 25 kg bags, or in bulk in super bags, hopper cars that protect it from
contamination. If stored under certain conditions as high relative humidity and / or exposed to large temperature
variations, condensation inside the package is possible. Under such circumstances it is advisable to allow the resin to dry
prior to use. Such unfavorable storage conditions may enhance the characteristic odor of the resin.
The storage and handling of the resin should consider the protection of the resin from direct exposure to the sun,
temperatures above 40 ° C and humidity in the environment. Exposure to any of these conditions will decrease the
storage time of the resin.
The user should review the information on the product safety data sheet prior to use and handling.
INDELPRO can prohibit or restrict the use of your products for certain applications. For more information, please contact
your INDELPRO´s representative.
The information presented here is a product of the observation of previous experiences. In view of the various factors that could affect the
processing and different applications, this information does not exempt the responsibility of the one who processes the material to perform
its own analyzes and tests, nor does it imply any legal assurance of certain properties or characteristics for a use specific. This information
does not remove the user’s obligation to inspect the material upon arrival and notify INDELPRO of any anomaly immediately. It is the
responsibility of whoever is provided with the product to ensure and enforce any legislation regarding property rights.
INDELPRO does not give any additional warranties, express or implied, for example, warranties of merchantability or of specific
applications in the use of this material. The solution to any claim with respect to the material is the replacement of the same and in no case
INDELPRO shall be liable for incidental or consequential damages. The use of the product indicates the acceptance of the above
mentioned.